SSM25第三代手涂型聚脲修補涂層
SSM25 Third generation hand-applied polyurea repair coating
一、產品介紹Product introduction
SSM25 第三代手涂型聚脲修補涂層是德國Drache Handels UG 公司于二十一世紀
研發的一種雙組分芳香族手涂型聚脲修補材料，用于各種防水修繕，適合于混凝土、鋼結構，彩鋼板等，同時又是針對噴涂聚脲彈性體施工而研發的配套產品。它能幫助解決噴涂聚脲彈性體涂層施工后因意外損壞部位的修復，以及不易噴涂施工部位的小面積涂裝。
SSM25 third generation hand applied polyurea repair coating is Drache Handels UG companyfrom German in the 21st century Developed a two-component aromatic hand-coated polyurea repair material, used for a variety of waterproof repair, suitable for concrete, steel structure, color steel plate, etc., but also for spraying polyurea elastomer construction and research and development of supporting products. It can help solve the problem of repairing the parts damaged by accident after the construction of spraying polyurea elastomer coating, as well as the small area coating of the construction parts that are not easy to spray.
二、產品特性Product characteristics
? 高固體含量，低VOC排放，施工安全環保。
? 施工簡便，無需使用專業聚脲噴涂設備；可刷涂、刮涂。
? 固化速度快，一次涂裝成膜厚，更有利于立面施工。
? 涂層光滑平整、致密堅固、附著力強，能與噴涂聚脲彈性體涂層合為一體，并具有與之相當?shù)奈锢硇阅堋?
? 與噴涂聚脲彈性體涂層相容性好、粘結力強，避免發生分層現象。
? 優異的耐化學介質腐蝕性能，可耐一定濃度的酸、堿、鹽、油、有機溶劑等
? 使用溫度范圍寬，可在-10℃~120℃的環境下使用
? High solid content, low VOC emission, safe construction and environmental protection.
? Simple construction, no need to use professional polyurea spraying equipment; It can be brushed and scraped.
? Fast curing speed, a thick coating film, more conducive to facade construction.
? The coating is smooth, compact and strong, and can be integrated with the sprayed polyurea elastomer coating, and has comparable physical properties.
? Good compatibility and strong adhesion with sprayed polyurea elastomer coating to avoid delamination.
? Excellent corrosion resistance to chemical media, can withstand a certain concentration of acid, alkali, salt, oil, organic solvents, etc
? Wide temperature range, can be used in -10℃~120℃ environment
三、產品應用范圍Product application range
適用于混凝土、鋼結構，彩鋼板等防水修繕，同時又是針對噴涂聚脲彈性體施工而研發的配套產品。
Suitable for concrete, steel structure, color steel plate and other waterproof repair, but also for spraying polyurea elastomer construction and research and development of supporting products.
四、技術參數Technical parameter
產品物理屬性Physical property of product
|
項目 |
結果 |
|
外觀 |
顏色可調 |
|
比重（g/cm3 ） |
1.05 |
|
粘度(cps )@20℃ |
800 |
|
固含量（%） |
≥70 |
|
表干時間（小時） |
1-3 |
|
活化期（小時） |
20min |
|
理論涂布率 |
0.7kg/m2(厚度500um) |
典型物理測試性能 Typical physical test performance
|
項目 |
測試標準 |
結果 |
|
硬度(邵氏A) |
ASTM D-2240 |
80 |
|
伸長率（%） |
ASTM D-412 |
250 |
|
拉伸強度（Mpa） |
ASTM D-412 |
12 |
|
撕裂強度(kN/m) |
ASTM D-624 |
55 |
|
耐磨測試(750g/500r),mg |
HG/T 3831-2006 |
8.9 |
|
附著力（Mpa）鋼基材 |
HG/T 3831-2006 |
9.2 |
|
附著力（Mpa）混凝土基材 |
HG/T 3831-2006 |
3.0 |
|
抗沖擊性能（kg.m） |
GB/T23446-2009 |
1.0 |
|
密度（g/cm3） |
GB/T 6750-2007 |
1.2 |
耐腐蝕性能Corrosion resistance
|
耐酸性 30%H2SO4或10%HCl,30d |
無腐蝕，不起泡，不脫落 |
|
耐堿性30%NaOH, 30d |
無腐蝕，不起泡，不脫落 |
|
耐鹽性30g/L,30d |
無腐蝕，不起泡，不脫落 |
|
耐鹽霧，2000h |
無腐蝕，不起泡，不脫落 |
|
耐油性0號柴油，原油，30d |
無腐蝕，不起泡，不脫落 |
|
（僅供參考：需要注意揮發，濺蝕，溢出等影響，如需詳細數據，推薦用戶自己進行浸泡測試） |
|
產品固化時間Product curing time
|
基材溫度 |
表干 |
步行強度 |
完全固化 |
|
+10℃ |
3h |
24h |
7d |
|
+20℃ |
2h |
12h |
6d |
|
+30℃ |
1h |
8h |
5d |
注：以上固化時間會因環境情況的變化而有所不同，尤其是溫度和相對濕度的變化。
五、施工注意事項Construction precautions
? 施工設備及應用指導
推薦干膜厚度：500-1000um
覆涂間隔：4-24h
建議涂裝方法:刷涂、刮涂
? Construction equipment and application guidance
Recommended dry film thickness: 500-1000um
Coating interval: 4-24h
Recommended coating method: brush coating, scraping coating
?施工環境
環境溫度:-5 --35℃，相對濕度：35-85%
露點：金屬材質表面施工時必須大于露點溫度3℃以上。
? Construction environment
Ambient temperature :-5 --35℃, relative humidity: 35-85%
Dew point: Metal surface construction must be greater than the dew point temperature of 3℃ or more.
?施工基層處理
金屬表面：建議噴砂除銹，達到ISO8501-1或GB8923標準的Sa2.5級。
混凝土表面：達到堅固、密實、平整、干凈、干燥狀態。不應有起砂、起殼、裂縫、蜂窩麻面等現象。通常需要用膩子修補。
木材表面：干凈，干燥，沒有毛刺，碎片和松散的碎片。
其它材質基層的應用處理可咨詢圣士曼技術人員。
? Construction base treatment
Metal surface: It is recommended to sand blast to remove rust, to ISO8501-1 or GB8923 standard Sa2.5.
Concrete surface: solid, dense, flat, clean, dry state. There should be no sand, shell, cracks, honeycomb and other phenomena. It usually needs to be repaired with putty.
Wood surface: clean, dry, free of burrs, chips and loose debris.
The application of other material bases can be consulted by the Saint Si Man technicians.
?產品使用注意事項
按要求配比調好，用多少配多少，攪拌均勻后使用。
配漆后，包裝桶內的原料必須蓋嚴，防止吸潮。
施工過程中保持干燥清潔，嚴禁與水、醇、酸、堿等接觸。
? Product use precautions
Adjust the ratio according to the requirements, how much to use, stir well after use.
After painting, the raw materials in the packing bucket must be tightly covered to prevent moisture absorption.
Keep it dry and clean during construction, and do not contact with water, alcohol, acid, alkali, etc.
?產品包裝及保質期
包裝：10公斤/桶
產品保質期：12個月（未開封）。儲存環境溫度：5℃-35℃
在陰涼、通風的環境下儲存，避免陽光直射，遠離熱源。
? Product packaging and shelf life
Packing: 10 kg/barrel
Shelf life: 12 months (unopened). Storage ambient temperature: 5℃-35℃
Store in a cool, ventilated environment away from direct sunlight and away from heat sources.
六、誠信聲明Statement of good faith
圣士曼公司承諾以上所列各項產品數據是在相關實驗室相對應標準測試獲取，測試過程中相關數據會因測試環境和方法不同而結果略有差異。因此圣士曼公司建議客戶使用該產品前做好實地考察論證。除產品質量本身外，圣士曼公司不承擔任何責任并保證對以上數據進行調整和更新而不提前告知的權利，并請諒解。
The company promises that the above listed product data is obtained in the relevant laboratory corresponding to the standard test, and the relevant data will be slightly different due to the different test environment and method. Therefore, the company advises customers to conduct a field study before using the product. In addition to the quality of the product itself, the company does not assume any responsibility and guarantees the right to adjust and update the above data without prior notice.